Transmission Attributes (T)
PARAMETER MAXIMUM FIELD SIZE CODENAME DEFINITION XML Element
        <!--  T section  --> 
DATA  SOURCEID 32 T-x\ID DATA SOURCE ID CONSISTENT WITH GENERAL INFORMATION GROUP.  <TransmissionAttributes DataSource="">
SOURCE RF ATTRIBUTES   <SourceRFAttributes>
  <TransmitterID />
  <Frequency />
  <RFBandwidth />
  <DataBandwidth />
  <ModulationType />
  <TotalCarrierModulation />
  <Power />
<SourceRFAttributes>
TRANSMITTER ID 12 T-x\TID TRANSMITTER IDENTIFICATION
FREQUENCY 6 T-x\RF1 CARRIER FREQUENCY, IN MHz.  IF PROGRAMMABLE, ENTER 'P', AND DEFINE IN COMMENT RECORD.
RF BANDWIDTH 6 T-x\RF2 TOTAL RF BANDWITH (-60 dB) OFMODULATED SIGNAL, IN MHz.
DATA BANDWIDTH 6 T-x\RF3 COMPOSITE BASEBAND DATA BANDWIDTH (3 dB), IN kHz.
MODULATIONTYPE 8 T-x\RF4 DEFINE THE MODULATION TYPE:  'FM'     'PM'     'BPSK'     'DPSK'  'QPSK'      'OTHR'      'FQPSK-B'
TOTAL CARRIER MODULATION 6 T-x\RF5 FOR FM SYSTEM DEFINE TOTAL CARRIER DEVIATION, PEAK-TO-PEAK, IN kHz.  FOR PM SYSTEM DEFINE TOTAL PHASE MODULATION, PEAK-TO-PEAK, IN RADIANS.
POWER (RADIATED) 4 T-x\RF6 TOTAL TRANSMITTED POWER WHEN MODULATED, IN WATTS.
NUMBER OF SUBCARRIERS 2 T-x\SCO\N NUMBER OF SUBCARRIERS IN THE COMPOSITE BASEBAND WAVEFORM, n.  IF NONE, ENTER 'NO'.  
SUBCARRIER NUMBER 5 T-x\SCO1-n GIVE THE IRIG CHANNEL NUMBER FOR THE SUBCARRIER.  IF NONSTANDARD SUBCARRIER, ENTER 'NO',  AND ENTER FREQUENCY IN THE COMMENTS SECTION WHERE n IS AN IDENTIFICATION TAG FOR THE SUBCARRIER. <Subcarrier>
  <Number ModulationIndex = "" />
</Subcarrier>
<ModulatorNonLinearity />
MODULATION INDEX 4 T-x\SCO2-n SPECIFY THE MODULATION INDEX FOR EACH SUBCARRIER IN THE COMPOSITE WAVEFORM, AS APPROPRIATE.
MODULATOR NONLINEARITY 4 T-x\RF7 MODULATOR NONLINEARITY, IN PERCENT.
PREMODULATION FILTER   <PremodulationFilter>
  <Bandwidth />
  <Slope />
  <Type />
</PremodulationFilter>
BANDWIDTH 6 T-x\PMF1 PRE-MODULATION COMPOSITE FILTER BANDWIDTH, 3 dB CUT-OFF FREQUENCY, IN kHz.
SLOPE 2 T-x\PMF2 PRE-MODULATION FILTER ASYMPTOTIC ROLL-OFF SLOPE, dB/OCTAVE.
TYPE 2 T-x\PMF3 SPECIFY THE FILTER TYPE:CONSTANT AMPLITUDE - 'CA'CONSTANT DELAY - 'CD'OTHER - 'OT'
TRANSMIT ANTENNA   <TransmitAntenna>
  <Type />
  <Polarization />
  <Location />
</TransmitAntenna>
TRANSMIT ANTENNA TYPE 16 T-x\AN1 TRANSMIT ANTENNA TYPE.
TRANSMIT POLARIZATION 4 T-x\AN2 TRANSMIT ANTENNA POLARIZATION.'RHCP'   'LHCP'   LINEAR - 'LIN'
ANTENNA LOCATION 16 T-x\AN3 DESCRIBE THE ANTENNA LOCATION.
ANTENNA PATTERNS   <AntennaPatterns>
  <Document />
  <PointOfContact>
    <Name />
    <Agency />
    <Address />
    <Telephone />
  </PointOfContact>
</AntennaPatterns>
DOCUMENT 16 T-x\AP IDENTIFY DOCUMENT HAVING ANTENNA PATTERNS.
POINT OF CONTACT:
NAME
AGENCY
ADDRESS
TELEPHONE
24
48
48
20
T-x\AP\POC1
T-x\AP\POC2
T-x\AP\POC3
T-x\AP\POC4		 IDENTIFY THE POINT OF CONTACT FOR ADDITIONAL INFORMATION.
GROUND STATION ATTRIBUTES   <GroundStationAttributes>
  <IFBandwidth />
  <BasebandCompositeBandwidth />
</GroundStationAttributes>
IF BANDWIDTH 6 T-x\GST1 DEFINE THE IF BANDWIDTH (3 dB) IN MHz.
BASEBAND COMPOSITE BANDWIDTH 6 T-x\GST2 DEFINE THE CUTOFF FREQUENCY (3 dB), IN kHz, OF THE OUTPUT FILTER.
GAIN CONTROL   <GainControl>
  <AGCTimeConstant />
  <MGCGainSetPoint />
  <AFC_APC />
  <TrackingBandwidth />
  <PolarizationReception />
</GainControl>
AGC TIMECONSTANT 4 T-x\GST3 SPECIFY THE AGC TIME CONSTANT DESIRED IN MILLISECONDS.
MGC GAINSET POINT 6 T-x\GST4 PROVIDE THE MANUAL GAIN CONTROL SET POINT IN TERMS OF RECEIVED SIGNAL STRENGTH, dBm.
AFC/APC 3 T-x\GST5 SPECIFY AUTOMATIC FREQUENCY CONTROL ('AFC') OR AUTOMATIC PHASE CONTROL ('APC') OR NONE ('NON').
TRACKING BANDWIDTH 4 T-x\GST6 SPECIFY TRACKING LOOP BANDWIDTH IN Hz.
POLARIZATION RECEPTION 5 T-x\GST7 SPECIFY POLARIZATION TO BE USED:
RHCP - 'RHCP'
LHCP - 'LHCP'
BOTH - 'BOTH'
BOTH WITH DIVERSITY COMBINING:
PRE-DETECTION-'B&DPR'
POST-DETECTION-'B&DPO'
DIVERSITY COMBINING (ONLY):
PRE-DETECTION-'PRE-D'
POST-DETECTION-'POS-D'
OTHER - 'OTHER', SPECIFY IN COMMENTS.
FM SYSTEMS   <FMSystems>
  <DiscriminatorBandwidth />
  <DiscriminatorLinearity />
</FMSystems>
DISCRIMINATOR BANDWIDTH 4 T-x\FM1 SPECIFY THE DISCRIMINATOR BANDWIDTH REQUIRED IN MHz.
DISCRIMINATOR LINEARITY 4 T-x\FM2 SPECIFY THE REQUIRED LINEARITY OVER THE BANDWIDTH SPECIFIED.
PM SYSTEMS   <PMSystems>
  <PhaseLockLoopBandwidth />
</PMSystems>
PHASE LOCK LOOP BANDWIDTH 4 T-x\PLL SPECIFY THE PHASE LOCKED LOOP BANDWIDTH.
COMMENTS    
COMMENTS 1600 T-x\COM PROVIDE THE ADDITIONAL INFORMATION REQUIRED TO COMPLETE THE ABOVE INFORMATION REQUESTED OR TO PROVIDE ANY OTHER INFORMATION THAT IS DESIRED. <Comments />